4F illumec™ Series Datasheet by MEC Switches

PANEL SWITCHES
• Recommended load :
- Gold contacts : 0.5µ-50mA 24VDC
- Silver contacts : 0.5-50mA 24VDC
• Contact resistance : <30mΩ - typically 10mΩ
• Insulation resistance : >10MΩ
• Contact bounce : <2mS - typically 0.5mS
ELECTRICAL SPECIFICATIONS
• Switch sealing : IP67 according to IEC 60529
• Working and storage temperature : -30°C/+85°C
• Soldering :
- through-hole : IEC 68-2-20 8
- surface mount : JEDEC J-STD-020C
ENVIRONMENTAL SPECIFICATIONS
• Standard actuation force : 3.5N
• Max. actuation force : 100N for 10 sec
• Travel : 1 mm
• Lifetime : >10,000,000 cycles
MECHANICAL SPECIFICATIONS
10 x 10 mm ; h=10.4 mm
Illumination with integrated chip-LEDs
Single or bi-color illumination
Momentary NO
Simple slip-on cap retention system
DISTINCTIVE FEATURES
Illumec™ 4F
Illuminated switches • slip-on cap
retention system • integrated chip-LEDs
• Housing : PPS UL94V0
• Actuator : PPS UL94V0
• Sealing : Silicone rubber
• Contacts spring : Stainless steel
Silver : +3µAg
Gold : +1µAu
• Fixed contacts :
Silver : SnCu + 2µNI + 3µAg
Gold : SnCu + 2µNI + 1µAu
• Terminals : SnCu + 2µNI + 3µSn100
MATERIALS
The company reserves the right to change specifications without notice. All tolerance if not otherwise specified ±0.2mm.
369
PCB SWITCHES
For full series information:
www.apem.com
Illum «ms % m ‘Mm ms W125
Illuminated switches • slip-on cap
retention system • integrated chip-LEDs
Illumec™ 4F
4FSH9XX
4FTH9XX
All tolerances unless otherwise noted : ±0.2 mm
• TH
• NO
• Single or bi-color LEDs
• SMD
• NO
• Single or bi-color LEDs
weiV poT
weiV poT
weiV poT
weiV poT
weiV poT
weiV poT
weiV poT
weiV poT
TH SMD
PCB LAYOUT & CIRCUIT DIAGRAM
SINGLE LED
TH SMD
BI-COLOR - 2 LEDS
PCB SWITCHES
370
PANEL SWITCHES
BUILD YOUR PART NUMBER
ILLUMINATED
01 blue
22 green
29 high intesity green
42 yellow
61 white
82 red
2242 green/yellow
8222 red/green
8242 red/yellow
LED
SERIES
4F
TH9 through-hole
SH9 surface mount
MOUNTING
ABOUT THIS SERIES
Notice : Refer to www.apem.com for further information.
Accessories : See the website for 4F cap and bezel options
Illumec™ 4F
Illuminated switches • slip-on cap
retention system • integrated chip-LEDs
371
PCB SWITCHES
| 9
PART NO. ORDERING CODE PITCH QUANTITY
PER REEL
4FSH901 4FSH901R 20 250
4FSH922 4FSH922R 20 250
4FSH942 4FSH942R 20 250
4FSH961 4FSH961R 20 250
4FSH982 4FSH982R 20 250
4FSH92242 4FSH92242R 20 250
4FSH98222 4FSH98222R 20 250
4FSH98242 4FSH98242R 20 250
• Reel diameter: Ø330 mm
• Tape width:24 mm
• Pitch: see list
• Tape and reel material : antistatic or better
• Quantity per reel : see list
MOUNTING
SPACE REQUIREMENT - MATRIX MOUNTING
Tape and reel is available for the parts listed and has the
following specifications
TAPE & REEL
through-hole (TH)
surface mount (SMD)
*/F=20mA, **Pulse width 1ms Duty cycle 1:5, ***/F=50mA, ****Luminous Flux mlm
Illuminated switches • slip-on cap
retention system • integrated chip-LEDs
Illumec™ 4F
LED COMPONENT SPECIFICATIONS
Color Blue Green Yellow White Red High Intensity Green
Color Codes 01 22 42 61 82 29
ABSOLUTE MAXIMUM RATINGS (Ta=25°C)
Power mW 110 75 60 48 65 102.5
Current forward mA 25 30 25 15 25 25
Forward peak current mA 100 80 60 100 100 150
Voltage reverse V 5 5 5 NA 12 5
Operating
temperature °C -40/+85 -55/+85 -40/+85 -40/+85 -30/+85 -40/+85
Storage temperature °C -40/+85 -55/+85 -40/+90 -40/+85 -40/+85 -40/+85
Soldering temperature °C 5 245 for max. 10 sec
ELECTRICAL-OPTICAL CHARACTERISTICS (Ta=25°C)
Voltage forward Typ. V 3.3 2 1.75** 2.85 2 3.3
Max. V 3.7 2.4 2.35 3.1 2.5 4.1
Current reverse (VR=5V) Max. µA 50 100 10 NA 100 50
Wave length nm 468 571 591 NA 633 525
Spread nm 25 NA 15 NA 16 30
Spread angle degree 120 130 120 150 160 60
Luminous Intensity Min. mcd 28.5 18 28.5 71 28 500
Typ. mcd 72* 35 72* 224* 180* 1000
Optical intensity Lm/w NA NA NA 36 7 NA
PCB SWITCHES
372